USB3 Camera BU series
(CMOS, Compact・Rolling shutter)

BU602M / BU602MC / BU602MCF

USB3 Camera BU series (CMOS, Compact・Rolling shutter) BU602M series

USB3 Vision logo

  • USB3
  • 6.2 MP
  • 1/1.8 type
  • RS-CMOS
  • B/W
  • Color
  • 60 fps
  • TeliCore
  • image buffer

This BU series is an integrated-(one-body)-type camera that adopts all pixel data readout inter line CCD or CMOS.
For video output and camera control, the USB3.1 Gen1 (USB3.0) interface standard is adopted for high transfer rate, and it is easy to integrate into industrial equipment.

Key Features

  • High frame rate
  • USB3.1 Gen1 (USB3.0) interface
  • USB3 Vision Ver.1.0 conformity
  • GenICam conformity Ver.2.4 / Ver.3.0
  • IIDC2 Digital Camera Control Specification Ver.1.1.0
  • e-CON Connector adoption
  • Scalable
    Frame rate calculation tool
    (BU series CMOS camera)
  • Square grid arrangement
  • Random Trigger Shutter

Specifications

B/W Camera

BU602M Specifications table
Model BU602M
Interface USB3.1 Gen1 (USB3.0) (Only SuperSpeed is supported)
Pixels 6.2M
Imager CMOS image sensor
Imager model IMX178LLJ
Resolution 3,072(H) x 2,048(V)
Frame rate 60fps (Mono 8bit)
Pixel size 2.40μm x 2.40μm
Scanning area 7.37mm(H) x 4.92mm(V)
Image size 1/1.8 type
Aspect ratio 3:2
Scanning Progressive
Electronic shutter method MANUAL : Rolling shutter / Random Trigger Shutter : Global reset
Random Trigger Shutter Type External Trigger / Software Trigger
Random Trigger Shutter Mode Edge / Level / Bulk (255 times)
Sequential Shutter 16 entries (max)
Exposure Time MANUAL : 23.3μs to 16s
AE : 23.3μs to 16s
Random Trigger Shutter : 23.3μs to 16s (Edge or Bulk mode), 50μs to Trigger width (Level mode)
Synchronization System Internal / Bus (USB)
Optical glass/filter -
Sensitivity 2,100 lx
(F5.6, 1/62.5s)
Minimum illuminance 5 lx
(F1.4, Gain: +24dB, Video level: 50%)
Gain MANUAL : 0 to +24dB, AGC : 0 to +24dB
Black Level -25% to +25%
Gamma / LUT γ=1.0 to 0.45 / In 12bit, Out 12bit
Image Buffer 256MB / 42 frames (all pixels readout)
Image Output Format Mono 8bit / Mono 10bit / Mono 12bit
Readout Mode All pixel, Scalable, Mirroring, Flip
External trigger input Low: 0 to 0.5V, High: 2 to 24.0V
High active / Low active, Pulse width: 50μs (minimum)
Power supply DC5V±5%
Power consumption 2.4W max.
Lens mount C-mount
External dimension 29(W) x 29(H) x 16(D) mm (Not including protruding parts)
Mass approx. 33g
Operation temperature 0°C to 40°C (below 60°C on cabinet surface)
Operation humidity 10% to 90% (no condensation)
Conformity CE, FCC, RoHS, WEEE, USB3 Vision, GenICam, IIDC2

Color Cameras

BU602MC / BU602MCF Specifications table
Model BU602MC BU602MCF
Interface USB3.1 Gen1 (USB3.0) (Only SuperSpeed is supported)
Pixels 6.2M
Imager CMOS image sensor
Imager model IMX178LQJ
Resolution 3,072(H) x 2,048(V)
Frame rate 60fps (Bayer 8bit, Mono 8bit)
Pixel size 2.40μm x 2.40μm
Scanning area 7.37mm(H) x 4.92mm(V)
Image size 1/1.8 type
Aspect ratio 3:2
Scanning Progressive
Electronic shutter method MANUAL : Rolling shutter / Random Trigger Shutter : Global reset
Random Trigger Shutter Type External Trigger / Software Trigger
Random Trigger Shutter Mode Edge / Level / Bulk (255 times)
Sequential Shutter 16 entries (max)
Exposure Time MANUAL : 23.3μs to 16s
AE : 23.3μs to 16s
Random Trigger Shutter : 23.3μs to 16s (Edge or Bulk mode), 50μs to Trigger width (Level mode)
Synchronization System Internal / Bus (USB)
On-chip Color Filter RGB primary color mosaic-on-tip color filter
Optical glass/filter - IR Cut Filter
Sensitivity 3,000 lx
(F5.6, 1/62.5s)
3,400 lx
(F5.6, 1/62.5s)
Minimum illuminance 6 lx
(F1.4, Gain: +24dB, Video level: 50%)
7 lx
(F1.4, Gain: +24dB, Video level: 50%)
Gain MANUAL : 0 to +24dB, AGC : 0 to +24dB
Black Level -25% to +25%
Gamma / LUT γ=1.0 to 0.45 / In 12bit, Out 12bit
White balance Manual white-balance / One-push white-balance
Image Buffer 256MB / 42 frames (all pixels readout)
Image Output Format RGB 24bit, BGR 24bit, YUV422 16bit, YUV411 12bit, Bayer 8bit / Bayer 10bit / Bayer 12bit, Mono 8bit
Readout Mode All pixel, Scalable, Mirroring, Flip
External trigger input Low: 0 to 0.5V, High: 2 to 24.0V
High active / Low active, Pulse width: 50μs (minimum)
Power supply DC5V±5%
Power consumption 3W max.
Lens mount C-mount
External dimension 29(W) x 29(H) x 16(D) mm (Not including protruding parts)
Mass approx. 33g
Operation temperature 0°C to 40°C (below 60°C on cabinet surface)
Operation humidity 10% to 90% (no condensation)
Conformity CE, FCC, RoHS, WEEE, USB3 Vision, GenICam, IIDC2

Other Documents

Thermal design guide line