Topics
Thank you and report of "International Technical Exhibition on Image Technology and Equipment 2021"
Toshiba Teli Corporation participated in the International Technical Exhibition on Image Technology and Equipment (ITE) 2021 held at PACIFICO Yokohama from December 1st (Wed) to December 3rd (Fri) to showcase high-pixel-count cameras with CoaXPress 2.0, Dual USB3, USB3, and other interfaces, various industrial cameras with different interfaces (CoaXPress, USB3, GigE, Camera Link cameras), and diverse inspection solutions.
We would like to express our sincere gratitude for all the people who visited our booth.
[ Teli booth introduction video (Digest version) ]
* Japanese only
Descriptions of our booth
Our booth consisted of the following ten sections, each of which is described below;
- CoaXPress 2.0 camera EX series; EX670AMG-X (New product)
- 20MP RS-CMOS camera; BU2006M series (Under development)
- C-mount camera with Gen-4 24.5MP Pregius S; BU2409MCF (New product)
- Cameras with a Dual USB3 interface realizing 10Gbps transfer bandwidth; DDU1607MCF (New product)
- AI visual inspection software; PEKAT VISION
- RGB+NIR 5.3MP CMOS camera; DU535MCNE (Reference exhibit)
- InGaAs line camera
- Imaging IoT system
- Industrial cameras lineup
1. CoaXPress 2.0 camera; EX670AMG-X (New product)
We showcased the EX670AMG-X 67-million-pixel (67MP) CMOS monochrome camera with four lanes of the latest CoaXPress V2.0 CXP-12 interface.
[ Product introduction ]
[ Cameras and software used ]
- EX670AMG-X
https://www.toshiba-teli.co.jp/en/products/industrial-camera/coaxpress-camera-ex-ex670.htm - TeliViewer (TeliCamSDK v4.0.1.1)
https://www.toshiba-teli.co.jp/en/products/industrial-camera/software-telicamsdk.htm
[ Product leaflet ]
[ Download a document containing exhibition panel image ]
2. 20MP RS-CMOS camera; BU2006M series (Under development)
We demonstrated the shooting of high-definition images of the 20.44-million-pixel (20MP) camera BU2006M series equipped with the backside-illuminated CMOS sensor from Sony Corporation.
[ Cameras and software used ]
- BU2006MG (Under development)
- BU602M
https://www.toshiba-teli.co.jp/en/products/industrial-camera/usb-camera-bu602m.htm - TeliViewer (TeliCamSDK v4.0.1.1)
https://www.toshiba-teli.co.jp/en/products/industrial-camera/software-telicamsdk.htm
[ Download a document containing exhibition panel image ]
3. C-mount camera with Gen-4 24.5MP Pregius S; BU2409MCF (New product)
We demonstrated the BU2409MCF color camera incorporating the Gen-4 24.47-million-pixel (24.5MP) "Pregius S" backside-illuminated CMOS image sensor from Sony Corporation.
[ Cameras and software used ]
- BU2409MCF
https://www.toshiba-teli.co.jp/en/products/industrial-camera/usb-camera-bu2409m.htm - TeliViewer (TeliCamSDK v4.0.1.1)
https://www.toshiba-teli.co.jp/en/products/industrial-camera/software-telicamsdk.htm
[ Download a document containing exhibition panel image ]
4. Cameras with a Dual USB3 interface realizing 10Gbps transfer bandwidth; DDU1607MCF (New product)
We showcased a unique Dual USB3 camera with two channels of the USB 3.1 Gen 1 interface.
[ Cameras and software used ]
- DDU1607MCF
https://www.toshiba-teli.co.jp/en/products/industrial-camera/usb-camera-ddu1607m.htm - TeliViewer (TeliCamSDK v4.0.1.1)
https://www.toshiba-teli.co.jp/en/products/industrial-camera/software-telicamsdk.htm
[ Download a document containing exhibition panel image ]
- [ Cameras with a Dual USB3 interface realizing 10Gbps transfer bandwidth (in Japanese) ]
* An English version will be published as soon as it becomes available.
5. AI visual inspection software; PEKAT VISION (Only for domestic sales in Japan)
We demonstrated a scratch inspection for camera chassis, combining the PEKAT VISION deep-learning software from PEKAT s.r.o. in Czechoslovakia and Teli’s camera.
It required only two to three hours to teach the AI engine to recognize scratches and three to four hours for the learning, verification, and tuning of the AI engine. PEKAT VISION allowed us to create a highly accurate model in a relatively short time.
For the teaching work, we prepared only 30 sets of images of chassis with and without a scratch. You can provide a teaching set of images for PEKAT VISION simply by tracing scratches on the PEKAT VISION GUI just like on a graphics editor. Then, on a single click, PEKAT VISION does the rest of the work from learning to verification.
[ Cameras and software used ]
- PEKAT VISION
- BU238M
https://www.toshiba-teli.co.jp/en/products/industrial-camera/usb-camera-bu238m.htm
[ Download a document containing exhibition panel image ]
6. RGB+NIR 5.3MP CMOS camera; DU535MCNE (Reference exhibit)
We demonstrated an RGB+NIR camera DU535MCNE with a 5.33-million-pixel (5.3MP) CMOS image sensor capable of capturing visible and near-infrared (NIR) light simultaneously.
The demonstration was designed to inspect the printing conditions on the surface of packages via RGB images and internal foreign substances and dents via NIR images at the same time.
Since one of the pixels of the color filter of this camera is allocated to the NIR region, it is capable of simultaneous capture of RGB and NIR images, eliminating the need to build a large system composed of multiple monochrome, color, and other types of cameras and therefore making it possible to reduce system size.
[ Cameras and software used ]
- RGB+NIRcamera DU535MCNE (Tentative name)
- Dedicated viewer software
[ Download a document containing exhibition panel image ]
7. InGaAs line camera
We demonstrated an InGaAs line camera with a spectral sensitivity of 900 to 1,700 nm.
[ Cameras and software used ]
- InGaAs line camera; Cobra1000-GE512-10S-01
[ Download a document containing exhibition panel image ]
8. Imaging IoT system
We introduced the concept product of the imaging IoT system for smart factories as a system solution proposal that makes it easy for anyone to easily visualize on-site work.
[ Cameras and software used ]
[ Download a document containing exhibition panel image ]
9. Industrial cameras lineup
We exhibited a panel showing the lineup of our major industrial cameras by interface and put them on display.
[ Camera series listings ]
- CoaXPress Camera EX Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-coaxpress-camera-ex - Dual USB3 / USB3 Vision Camera DDU Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-usb-camera-ddu
- USB3 / USB3 Vision Camera DU Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-usb-camera-du - USB3 / USB3 Vision Camera BU Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-usb-camera-bu - GigE / GigE Vision Camera BG Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-gige-camera-bg - Camera Link Camera BC Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-cameralink-bc - Camera Link Camera CSC Series
https://www.toshiba-teli.co.jp/en/products/industrial-camera/index.htm#cat-cameralink-csc
Click here for larger image
International Imaging Seminar 2021
At the International Imaging Seminar held simultaneously with the ITE, Teli’s engineer presented a seminar entitled “IoT / AI proposal by Toshiba Teli”.
[ Seminar lecture video ]
* Japanese only
[ Seminar material ]
Thank you for taking time in your busy schedule to attend the seminar.
* Pregius, Pregius logo, Pregius S, Pregius S logo are trademarks of Sony Corporation.
* Company name, logo or other names are trademark or registered trademark of related companies in some cases
Information including specifications, content of services and contact information, is current on the date of the press announcement, but is subject to change without prior notice.